What can we help you with?

1. Open the MySOLEM app.
2. Connect to the controller via Bluetooth.
3. Open Settings by tapping the Edit (gear) icon in the upper-right corner of the screen.
4. Select « Retrieve controller data ».

The pressure switch uses a normally closed (NC) contact.

1. Install the pressure switch on the irrigation pipe.
2. Remove the cap from the pressure switch.
3. Connect to the device via Bluetooth using the app and select « Instant Value ». Verify that the displayed value is 0.
4. Start irrigation and verify that the value changes to 1.
5. To fine-tune the pressure switch, while irrigation is running, tighten the adjustment screw until the value changes to 0.
6. Then, with irrigation still running, slowly loosen the adjustment screw until the value changes back to 1.

Note: You can also use a multimeter instead of the Instant Value function to perform this adjustment.

To disable or enable notifications generated by sensor alerts:

1. Log in to your MySOLEM account on the MySOLEM platform.
2. Go to the « My Account » tab.
3. Locate the « Alerts » section.
4. Enable or disable alert notifications as desired.

1. Open the MySOLEM app or log in to the MySOLEM platform.
2. Select the controller you want to manage.
3. Set the controller to OFF to disable it or ON to re-enable it.

The number of controllers that can be paired depends on the gateway model:

• LR-MB10: Up to 10 controllers
• LR-MB30: Up to 30 controllers
• LR-BST-REACT: Up to 25 controllers
• Irrigation Station: Up to 24 controllers

Access to the Professional Account requires an activation request submitted directly through the MySOLEM.com platform. Once your request has been reviewed and approved by the SOLEM team, your account allows you to offer module management services to your customers.

When you send a management request to a user through the MySOLEM.com platform, they can choose whether to grant you access to their devices and permission to modify their programs.

Solid green LED: Normal operation.

Flashing green LED: A watering zone is currently running. The number of flashes corresponds to the active station number.

Flashing orange LED: Firmware update in progress.

Orange LED flashing 4 times: Short circuit detected on a station.

Solid red LED: The controller is in setup mode for 2 minutes.

Rapidly flashing red LED: Fault detected (open sensor or flow threshold reached). Watering is suspended, but the program continues to run. If the fault is cleared, watering resumes automatically. The number of flashes corresponds to the station that is currently inactive.

Red LED flashing 2 times: The controller has lost its time settings. Reconnect to the controller to resynchronize the clock.

Red LED flashing 3 times: Wi-Fi connection lost (incorrect Wi-Fi password entered, controller installed too far from the router, or Internet connection unavailable).

Red LED flashing 4 times: A station has a short circuit or overcurrent condition, or the controller was powered off and back on twice in a short period while a station was running.

Red LED flashing 5 times: The controller setup process timed out. Please repeat the setup procedure.

LED off: The controller is not receiving power.

The LEDs are active for one hour after startup. After this period, the gateway enters sleep mode.

Solid green LED: Normal operation.

Flashing green LED: LoRa communication.

Red LED flashing 3 times: GSM network connection lost.

Red LED flashing 2 times: Time synchronization alarm. The gateway’s clock is no longer synchronized. If your gateway is connected to the MySOLEM platform, the time will be synchronized automatically. Otherwise, connect to the LR-BST-REACT using the MySOLEM app and verify that the message « Synchronization OK » is displayed.

Flashing white LEDs: Searching for the best available network.

Flashing blue LEDs: Communicating with the MySOLEM platform.

Creating a MySOLEM user account allows you to:

• Automatically back up installed products and their associated programs to the MySOLEM platform, ensuring that all data can be restored if the user’s phone is lost, damaged, or experiences a system failure.
• Delegate programming management to a trusted person (for Bluetooth®-enabled products).
• Expand the range of services offered to customers by providing a service contract (for professional users).
• Enable the anti-theft feature.

The data collected is used exclusively for SOLEM’s online services and internal operations, in accordance with SOLEM’s contractual terms and conditions.

To connect your SOLEM product via Bluetooth, follow these steps:
1. Download and open the MySOLEM application on your smartphone.
2. Activate Bluetooth and nearby device location on your smartphone.
3. Select the “+” or press “add a controller” to add a new product.
Follow the on-screen instructions to complete the pairing.

To connect your SOLEM product via Bluetooth, follow these steps:
1. Download and open the MySOLEM application on your smartphone.
2. Activate Bluetooth and nearby device location on your smartphone.
3. Select the “+” or press “add a controller” to add a new product.
Follow the on-screen instructions to complete the pairing.

Solid green LED: Normal operation.

Flashing green LED: Firmware update in progress.

Red LED flashing 3 times: There are several possible causes:

• Wi-Fi access point (router) lost or connection not established. Restart both your router and the LR-MB.

• Incorrect Wi-Fi password entered during setup. Recommendation: Save your Wi-Fi password in a notes app on your mobile device. Press and hold to copy the password, then paste it into the appropriate field. Repeat the setup process.

• The LR-MB may be too far from the router during setup. Move the device closer to the router and try again.

Red LED flashing 2 times: Time synchronization alarm. The LR-MB’s clock is no longer synchronized. If your device is connected to the MySOLEM platform, the time will be synchronized automatically. Otherwise, connect to the LR-MB using the app and verify that the message « Synchronization OK » is displayed.

LED off: The device is not receiving power.

To connect your SOLEM product via Bluetooth, follow these steps:
1. Download and open the MySOLEM app on your smartphone.
2. Activate Bluetooth and nearby device location on your smartphone.
3. Select the “+” or press “add a controller” to add a new product.
Follow the on-screen instructions to complete the pairing.